Current File : //usr/lib/modules/6.8.0-45-generic/build/drivers/pinctrl/Kconfig
# SPDX-License-Identifier: GPL-2.0-only
#
# PINCTRL infrastructure and drivers
#
menuconfig PINCTRL
bool "Pin controllers"
if PINCTRL
config GENERIC_PINCTRL_GROUPS
bool
config PINMUX
bool "Support pin multiplexing controllers" if COMPILE_TEST
config GENERIC_PINMUX_FUNCTIONS
bool
select PINMUX
config PINCONF
bool "Support pin configuration controllers" if COMPILE_TEST
config GENERIC_PINCONF
bool
select PINCONF
config DEBUG_PINCTRL
bool "Debug PINCTRL calls"
depends on DEBUG_KERNEL
help
Say Y here to add some extra checks and diagnostics to PINCTRL calls.
config PINCTRL_AMD
bool "AMD GPIO pin control"
depends on HAS_IOMEM
depends on ACPI || COMPILE_TEST
select GPIOLIB
select GPIOLIB_IRQCHIP
select PINMUX
select PINCONF
select GENERIC_PINCONF
help
The driver for memory mapped GPIO functionality on AMD platforms
(x86 or arm). Most of the pins are usually muxed to some other
functionality by firmware, so only a small amount is available
for GPIO use.
Requires ACPI/FDT device enumeration code to set up a platform
device.
config PINCTRL_APPLE_GPIO
tristate "Apple SoC GPIO pin controller driver"
depends on ARCH_APPLE
select PINMUX
select GPIOLIB
select GPIOLIB_IRQCHIP
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
select OF_GPIO
help
This is the driver for the GPIO controller found on Apple ARM SoCs,
including M1.
This driver can also be built as a module. If so, the module
will be called pinctrl-apple-gpio.
config PINCTRL_ARTPEC6
bool "Axis ARTPEC-6 pin controller driver"
depends on MACH_ARTPEC6
select PINMUX
select GENERIC_PINCONF
help
This is the driver for the Axis ARTPEC-6 pin controller. This driver
supports pin function multiplexing as well as pin bias and drive
strength configuration. Device tree integration instructions can be
found in Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt
config PINCTRL_AS3722
tristate "Pinctrl and GPIO driver for ams AS3722 PMIC"
depends on MFD_AS3722 && GPIOLIB
select PINMUX
select GENERIC_PINCONF
help
AS3722 device supports the configuration of GPIO pins for different
functionality. This driver supports the pinmux, push-pull and
open drain configuration for the GPIO pins of AS3722 devices. It also
supports the GPIO functionality through gpiolib.
config PINCTRL_AT91
bool "AT91 pinctrl driver"
depends on OF
depends on ARCH_AT91
select PINMUX
select PINCONF
select GPIOLIB
select OF_GPIO
select GPIOLIB_IRQCHIP
help
Say Y here to enable the at91 pinctrl driver
config PINCTRL_AT91PIO4
bool "AT91 PIO4 pinctrl driver"
depends on OF
depends on HAS_IOMEM
depends on ARCH_AT91 || COMPILE_TEST
select PINMUX
select GENERIC_PINCONF
select GPIOLIB
select GPIOLIB_IRQCHIP
select OF_GPIO
help
Say Y here to enable the at91 pinctrl/gpio driver for Atmel PIO4
controller available on sama5d2 SoC.
config PINCTRL_AXP209
tristate "X-Powers AXP209 PMIC pinctrl and GPIO Support"
depends on MFD_AXP20X
depends on OF
select PINMUX
select GENERIC_PINCONF
select GPIOLIB
help
AXP PMICs provides multiple GPIOs that can be muxed for different
functions. This driver bundles a pinctrl driver to select the function
muxing and a GPIO driver to handle the GPIO when the GPIO function is
selected.
Say Y to enable pinctrl and GPIO support for the AXP209 PMIC.
config PINCTRL_BM1880
bool "Bitmain BM1880 Pinctrl driver"
depends on OF && (ARCH_BITMAIN || COMPILE_TEST)
default ARCH_BITMAIN
select PINMUX
help
Pinctrl driver for Bitmain BM1880 SoC.
config PINCTRL_CY8C95X0
tristate "Cypress CY8C95X0 I2C pinctrl and GPIO driver"
depends on I2C
select GPIOLIB
select GPIOLIB_IRQCHIP
select PINMUX
select PINCONF
select GENERIC_PINCONF
select REGMAP_I2C
help
Support for 20/40/60 pin Cypress Cy8C95x0 pinctrl/gpio I2C expander.
This driver can also be built as a module. If so, the module will be
called pinctrl-cy8c95x0.
config PINCTRL_DA850_PUPD
tristate "TI DA850/OMAP-L138/AM18XX pull-up and pull-down groups"
depends on OF && (ARCH_DAVINCI_DA850 || COMPILE_TEST)
select PINCONF
select GENERIC_PINCONF
help
Driver for TI DA850/OMAP-L138/AM18XX pinconf. Used to control
pull-up and pull-down pin groups.
config PINCTRL_DA9062
tristate "Dialog Semiconductor DA9062 PMIC pinctrl and GPIO Support"
depends on MFD_DA9062
select GPIOLIB
help
The Dialog DA9062 PMIC provides multiple GPIOs that can be muxed for
different functions. This driver bundles a pinctrl driver to select the
function muxing and a GPIO driver to handle the GPIO when the GPIO
function is selected.
Say Y to enable pinctrl and GPIO support for the DA9062 PMIC.
config PINCTRL_DIGICOLOR
bool
depends on ARCH_DIGICOLOR || COMPILE_TEST
select PINMUX
select GENERIC_PINCONF
config PINCTRL_EQUILIBRIUM
tristate "Generic pinctrl and GPIO driver for Intel Lightning Mountain SoC"
depends on OF && HAS_IOMEM
depends on X86 || COMPILE_TEST
select PINMUX
select PINCONF
select GPIOLIB
select GPIO_GENERIC
select GPIOLIB_IRQCHIP
select GENERIC_PINCONF
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
help
Equilibrium driver is a pinctrl and GPIO driver for Intel Lightning
Mountain network processor SoC that supports both the GPIO and pin
control frameworks. It provides interfaces to setup pin muxing, assign
desired pin functions, configure GPIO attributes for LGM SoC pins.
Pin muxing and pin config settings are retrieved from device tree.
config PINCTRL_GEMINI
bool
depends on ARCH_GEMINI
default ARCH_GEMINI
select PINMUX
select GENERIC_PINCONF
select MFD_SYSCON
config PINCTRL_INGENIC
bool "Pinctrl driver for the Ingenic JZ47xx SoCs"
default MACH_INGENIC
depends on OF
depends on MIPS || COMPILE_TEST
select GENERIC_PINCONF
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
select GPIOLIB
select GPIOLIB_IRQCHIP
select REGMAP_MMIO
config PINCTRL_K210
bool "Pinctrl driver for the Canaan Kendryte K210 SoC"
depends on RISCV && SOC_CANAAN && OF
select GENERIC_PINMUX_FUNCTIONS
select GENERIC_PINCONF
select GPIOLIB
select OF_GPIO
select REGMAP_MMIO
default SOC_CANAAN
help
Add support for the Canaan Kendryte K210 RISC-V SOC Field
Programmable IO Array (FPIOA) controller.
config PINCTRL_KEEMBAY
tristate "Pinctrl driver for Intel Keem Bay SoC"
depends on ARCH_KEEMBAY || (ARM64 && COMPILE_TEST)
depends on HAS_IOMEM
select PINMUX
select PINCONF
select GENERIC_PINCONF
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
select GPIOLIB
select GPIOLIB_IRQCHIP
select GPIO_GENERIC
help
This selects pin control driver for the Intel Keem Bay SoC.
It provides pin config functions such as pull-up, pull-down,
interrupt, drive strength, sec lock, Schmitt trigger, slew
rate control and direction control. This module will be
called as pinctrl-keembay.
config PINCTRL_LANTIQ
bool
depends on LANTIQ
select PINMUX
select PINCONF
config PINCTRL_FALCON
bool
depends on SOC_FALCON
depends on PINCTRL_LANTIQ
config PINCTRL_LOONGSON2
tristate "Pinctrl driver for the Loongson-2 SoC"
depends on OF && (LOONGARCH || COMPILE_TEST)
select PINMUX
select GENERIC_PINCONF
help
This selects pin control driver for the Loongson-2 SoC. It
provides pin config functions multiplexing. GPIO pin pull-up,
pull-down functions are not supported. Say yes to enable
pinctrl for Loongson-2 SoC.
config PINCTRL_XWAY
bool
depends on SOC_TYPE_XWAY
depends on PINCTRL_LANTIQ
config PINCTRL_LPC18XX
bool "NXP LPC18XX/43XX SCU pinctrl driver"
depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
default ARCH_LPC18XX
select PINMUX
select GENERIC_PINCONF
help
Pinctrl driver for NXP LPC18xx/43xx System Control Unit (SCU).
config PINCTRL_MAX77620
tristate "MAX77620/MAX20024 Pincontrol support"
depends on MFD_MAX77620 && OF
select PINMUX
select GENERIC_PINCONF
help
Say Y here to enable Pin control support for Maxim MAX77620 PMIC.
This PMIC has 8 GPIO pins that work as GPIO as well as special
function in alternate mode. This driver also configure push-pull,
open drain, FPS slots etc.
config PINCTRL_MCP23S08_I2C
tristate
select REGMAP_I2C
config PINCTRL_MCP23S08_SPI
tristate
select REGMAP_SPI
config PINCTRL_MCP23S08
tristate "Microchip MCP23xxx I/O expander"
depends on SPI_MASTER || I2C
select GPIOLIB
select GPIOLIB_IRQCHIP
select GENERIC_PINCONF
select PINCTRL_MCP23S08_I2C if I2C
select PINCTRL_MCP23S08_SPI if SPI_MASTER
help
SPI/I2C driver for Microchip MCP23S08 / MCP23S17 / MCP23S18 /
MCP23008 / MCP23017 / MCP23018 I/O expanders.
This provides a GPIO interface supporting inputs and outputs and a
corresponding interrupt-controller.
config PINCTRL_MICROCHIP_SGPIO
tristate "Pinctrl driver for Microsemi/Microchip Serial GPIO"
depends on OF
depends on HAS_IOMEM
select GPIOLIB
select GPIOLIB_IRQCHIP
select GENERIC_PINCONF
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
select OF_GPIO
help
Support for the serial GPIO interface used on Microsemi and
Microchip SoCs. By using a serial interface, the SIO
controller significantly extends the number of available
GPIOs with a minimum number of additional pins on the
device. The primary purpose of the SIO controller is to
connect control signals from SFP modules and to act as an
LED controller.
If compiled as a module, the module name will be
pinctrl-microchip-sgpio.
config PINCTRL_OCELOT
tristate "Pinctrl driver for the Microsemi Ocelot and Jaguar2 SoCs"
depends on OF
depends on HAS_IOMEM
select GPIOLIB
select GPIOLIB_IRQCHIP
select GENERIC_PINCONF
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
select OF_GPIO
select REGMAP_MMIO
help
Support for the internal GPIO interfaces on Microsemi Ocelot and
Jaguar2 SoCs.
If conpiled as a module, the module name will be pinctrl-ocelot.
config PINCTRL_PALMAS
tristate "Pinctrl driver for the PALMAS Series MFD devices"
depends on OF && MFD_PALMAS
select PINMUX
select GENERIC_PINCONF
help
Palmas device supports the configuration of pins for different
functionality. This driver supports the pinmux, push-pull and
open drain configuration for the Palmas series devices like
TPS65913, TPS80036 etc.
config PINCTRL_PEF2256
tristate "Lantiq PEF2256 (FALC56) pin controller driver"
depends on OF && FRAMER_PEF2256
select PINMUX
select PINCONF
select GENERIC_PINCONF
help
This option enables the pin controller support for the Lantiq PEF2256
framer, also known as FALC56.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called pinctrl-pef2256.
config PINCTRL_PIC32
bool "Microchip PIC32 pin controller driver"
depends on OF
depends on MACH_PIC32
select PINMUX
select GENERIC_PINCONF
select GPIOLIB_IRQCHIP
select OF_GPIO
help
This is the pin controller and gpio driver for Microchip PIC32
microcontrollers. This option is selected automatically when specific
machine and arch are selected to build.
config PINCTRL_PIC32MZDA
def_bool y if PIC32MZDA
select PINCTRL_PIC32
config PINCTRL_PISTACHIO
bool "IMG Pistachio SoC pinctrl driver"
depends on OF && (MIPS || COMPILE_TEST)
depends on GPIOLIB
select PINMUX
select GENERIC_PINCONF
select GPIOLIB_IRQCHIP
select OF_GPIO
help
This support pinctrl and GPIO driver for IMG Pistachio SoC.
config PINCTRL_RK805
tristate "Pinctrl and GPIO driver for RK805 PMIC"
depends on MFD_RK8XX
select GPIOLIB
select PINMUX
select GENERIC_PINCONF
help
This selects the pinctrl driver for RK805.
config PINCTRL_ROCKCHIP
tristate "Rockchip gpio and pinctrl driver"
depends on ARCH_ROCKCHIP || COMPILE_TEST
depends on OF
select GPIOLIB
select PINMUX
select GENERIC_PINCONF
select GENERIC_IRQ_CHIP
select MFD_SYSCON
select OF_GPIO
default ARCH_ROCKCHIP
help
This support pinctrl and GPIO driver for Rockchip SoCs.
config PINCTRL_SINGLE
tristate "One-register-per-pin type device tree based pinctrl driver"
depends on OF
depends on HAS_IOMEM
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
select GENERIC_PINCONF
help
This selects the device tree based generic pinctrl driver.
config PINCTRL_ST
bool
depends on OF
select PINMUX
select PINCONF
select GPIOLIB_IRQCHIP
config PINCTRL_STMFX
tristate "STMicroelectronics STMFX GPIO expander pinctrl driver"
depends on I2C
depends on OF_GPIO
select GENERIC_PINCONF
select GPIOLIB_IRQCHIP
select MFD_STMFX
help
Driver for STMicroelectronics Multi-Function eXpander (STMFX)
GPIO expander.
This provides a GPIO interface supporting inputs and outputs,
and configuring push-pull, open-drain, and can also be used as
interrupt-controller.
config PINCTRL_SX150X
bool "Semtech SX150x I2C GPIO expander pinctrl driver"
depends on I2C=y
select PINMUX
select PINCONF
select GENERIC_PINCONF
select GPIOLIB
select GPIOLIB_IRQCHIP
select REGMAP
help
Say Y here to provide support for Semtech SX150x-series I2C
GPIO expanders as pinctrl module.
Compatible models include:
- 8 bits: sx1508q, sx1502q
- 16 bits: sx1509q, sx1506q
config PINCTRL_TB10X
bool
depends on OF && ARC_PLAT_TB10X
select GPIOLIB
config PINCTRL_TPS6594
tristate "Pinctrl and GPIO driver for TI TPS6594 PMIC"
depends on OF && MFD_TPS6594
default MFD_TPS6594
select PINMUX
select GPIOLIB
select REGMAP
select GPIO_REGMAP
select GENERIC_PINCONF
help
Say Y to select the pinmuxing and GPIOs driver for the TPS6594
PMICs chip family.
This driver can also be built as a module
called tps6594-pinctrl.
config PINCTRL_ZYNQ
bool "Pinctrl driver for Xilinx Zynq"
depends on ARCH_ZYNQ
select PINMUX
select GENERIC_PINCONF
help
This selects the pinctrl driver for Xilinx Zynq.
config PINCTRL_ZYNQMP
tristate "Pinctrl driver for Xilinx ZynqMP"
depends on ZYNQMP_FIRMWARE
select PINMUX
select GENERIC_PINCONF
default ZYNQMP_FIRMWARE
help
This selects the pinctrl driver for Xilinx ZynqMP platform.
This driver will query the pin information from the firmware
and allow configuring the pins.
Configuration can include the mux function to select on those
pin(s)/group(s), and various pin configuration parameters
such as pull-up, slew rate, etc.
This driver can also be built as a module. If so, the module
will be called pinctrl-zynqmp.
config PINCTRL_MLXBF3
tristate "NVIDIA BlueField-3 SoC Pinctrl driver"
depends on (MELLANOX_PLATFORM && ARM64) || COMPILE_TEST
select PINMUX
select GPIOLIB
select GPIOLIB_IRQCHIP
help
Say Y to select the pinctrl driver for BlueField-3 SoCs.
This pin controller allows selecting the mux function for
each pin. This driver can also be built as a module called
pinctrl-mlxbf3.
source "drivers/pinctrl/actions/Kconfig"
source "drivers/pinctrl/aspeed/Kconfig"
source "drivers/pinctrl/bcm/Kconfig"
source "drivers/pinctrl/berlin/Kconfig"
source "drivers/pinctrl/cirrus/Kconfig"
source "drivers/pinctrl/freescale/Kconfig"
source "drivers/pinctrl/intel/Kconfig"
source "drivers/pinctrl/mediatek/Kconfig"
source "drivers/pinctrl/meson/Kconfig"
source "drivers/pinctrl/mvebu/Kconfig"
source "drivers/pinctrl/nomadik/Kconfig"
source "drivers/pinctrl/nuvoton/Kconfig"
source "drivers/pinctrl/nxp/Kconfig"
source "drivers/pinctrl/pxa/Kconfig"
source "drivers/pinctrl/qcom/Kconfig"
source "drivers/pinctrl/realtek/Kconfig"
source "drivers/pinctrl/renesas/Kconfig"
source "drivers/pinctrl/samsung/Kconfig"
source "drivers/pinctrl/spear/Kconfig"
source "drivers/pinctrl/sprd/Kconfig"
source "drivers/pinctrl/starfive/Kconfig"
source "drivers/pinctrl/stm32/Kconfig"
source "drivers/pinctrl/sunplus/Kconfig"
source "drivers/pinctrl/sunxi/Kconfig"
source "drivers/pinctrl/tegra/Kconfig"
source "drivers/pinctrl/ti/Kconfig"
source "drivers/pinctrl/uniphier/Kconfig"
source "drivers/pinctrl/visconti/Kconfig"
source "drivers/pinctrl/vt8500/Kconfig"
endif
Mini Shell