Current File : //usr/lib/modules/6.8.0-45-generic/build/drivers/net/ethernet/freescale/Kconfig
# SPDX-License-Identifier: GPL-2.0-only
#
# Freescale device configuration
#
config NET_VENDOR_FREESCALE
bool "Freescale devices"
default y
depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
M523x || M527x || M5272 || M528x || M520x || M532x || \
ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
ARCH_LAYERSCAPE || ARCH_S32 || COMPILE_TEST
help
If you have a network (Ethernet) card belonging to this class, say Y.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Freescale devices. If you say Y, you will be
asked for your specific card in the following questions.
if NET_VENDOR_FREESCALE
config FEC
tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
ARCH_MXC || ARCH_S32 || SOC_IMX28 || COMPILE_TEST)
default ARCH_MXC || SOC_IMX28 if ARM
depends on PTP_1588_CLOCK_OPTIONAL
select CRC32
select PHYLIB
select PAGE_POOL
imply PAGE_POOL_STATS
imply NET_SELFTESTS
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX/S32 processors.
config FEC_MPC52xx
tristate "FEC MPC52xx driver"
depends on PPC_MPC52xx && PPC_BESTCOMM
select CRC32
select PHYLIB
select PPC_BESTCOMM_FEC
help
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
If compiled as module, it will be called fec_mpc52xx.
config FEC_MPC52xx_MDIO
bool "FEC MPC52xx MDIO bus driver"
depends on FEC_MPC52xx
default y
help
The MPC5200's FEC can connect to the Ethernet either with
an external MII PHY chip or 10 Mbps 7-wire interface
(Motorola? industry standard).
If your board uses an external PHY connected to FEC, enable this.
If not sure, enable.
If compiled as module, it will be called fec_mpc52xx_phy.
source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
source "drivers/net/ethernet/freescale/fman/Kconfig"
config FSL_PQ_MDIO
tristate "Freescale PQ MDIO"
select PHYLIB
help
This driver supports the MDIO bus used by the gianfar and UCC drivers.
config FSL_XGMAC_MDIO
tristate "Freescale XGMAC MDIO"
select PHYLIB
depends on OF
select MDIO_DEVRES
select OF_MDIO
help
This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
on the FMan mEMAC (which supports both Clauses 22 and 45)
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE && PPC32
select FSL_PQ_MDIO
select PHYLIB
select FIXED_PHY
help
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
config GIANFAR
tristate "Gianfar Ethernet"
depends on HAS_DMA
select FSL_PQ_MDIO
select PHYLIB
select FIXED_PHY
select CRC32
help
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
on the 8540.
source "drivers/net/ethernet/freescale/dpaa/Kconfig"
source "drivers/net/ethernet/freescale/dpaa2/Kconfig"
source "drivers/net/ethernet/freescale/enetc/Kconfig"
endif # NET_VENDOR_FREESCALE
Mini Shell